1, the construction and installation of wall surface, windows and other construction procedures have been completed and accepted.
2、基層清理。清理混凝土墻面上殘留的浮灰、脫模劑油污等雜物及抹灰空鼓部位等。剔除墻面接槎處劈裂的混凝土塊、夾雜物、空鼓等，并重新進行修補;窗臺挑檐按照2%用水泥砂漿找坡，外墻各種洞口填塞密實。要求粘貼聚苯板表面平整度偏差不超過4 mm，超差時對突出墻面處進行打磨，對凹進部位進行找補(需找補厚度超過6 mm時用1：3水泥砂漿抹灰，需找補厚度小于6mm時由保溫施工單位用聚合物黏結砂漿實施找補);以確保整個墻面的平整度在4 mm內，陰陽角方正、上下通順。
2, grass-roots clean-up. Clean up the residual concrete wall of dust, oil and other debris and release agent hollowing parts etc.. Remove wall joint at split concrete block, inclusions, cracks, hollowing, and re repair; window cornice with cement mortar with 2% sloping wall, all the packing density. The requirements of surface sticking polyphenyl plate flatness deviation is less than 4 mm, when the ultra poor of prominent wall was polished, the recessed part (Zhaobu to Zhaobu thickness more than 6 mm with 1:3 cement mortar plastering, Zhaobu required thickness is less than 6mm by thermal insulation construction unit for polymer bonded sand slurry to ensure the implementation of Zhaobu); the wall roughness in 4 mm, yin and yang angle founder, on smooth.
3、配制砂漿。施工使用的砂漿分為專用黏結砂漿及面層聚合物抗裂砂漿。施工時用手持式電動攪拌機攪拌，拌制的黏結砂漿質量比為水：砂漿=1：5，邊加水邊攪拌;攪拌時 間≥5 min，攪拌必須充分、均勻，稠度適中，并有一定黏度。砂漿調制完畢后，須靜置5 min，使用前再次進行攪拌，拌制好的砂漿應在1 h內用完。
3. Preparation of mortar. The mortar used in construction is divided into special adhesive mortar and surface polymer anti cracking mortar. The construction of a hand-held electric mixer, mixing the adhesive mortar ratio of mortar: water =1:5, while adding water and stirring; stirring time is more than 5 min, we must fully and evenly mixing, medium consistency, and has certain viscosity. After the mortar is finished, 5 min must be placed and stirred again before use. The mixed mortar should be used in 1 h.
在粘貼聚苯板前，在聚苯板粘貼面薄薄涂刷一道專用界面劑，可增強聚苯板與黏結砂漿的結合力;待界面劑晾干后方可涂抹聚合物黏結砂漿進行墻面粘貼施工。預粘板端翻包網格布在飄窗板、挑檐、陽臺、伸縮縫等位置預先粘貼板邊翻包網格布，將不小于220 mm寬的網格布中的80 mm寬用專用黏結砂漿牢固粘貼在基面上(黏結砂漿厚度不得超過2 mm)。
Before gluing polystyrene boards, a special interface agent is coated on the surface of polystyrene board to enhance the binding force of polystyrene board and bonded mortar. After the surface agent is dried, the polymer bonded mortar can be applied to the wall paste construction. Pre glued plate end ladle grid cloth in the windows board, cornice, balcony, and other joints position pre pasted plate edge ladle grid cloth, will not be less than 220 mm wide mesh in 80 mm wide with a special bonding mortar paste firmly on the surface (the thickness of bonding mortar shall not exceed 2 mm).
4. According to the construction drawings, the location line (middle line or border line) is popped out in the parts of the EPS component.
5. Cutting EPS components according to the size of the drawings. EPS components are standard dimensions, and splicing width should be considered when cutting.
6, when the EPS component is pasted, the grid cloth should be wrapped, and if there is a special case, it can be directly pasted without turning over the bag. The polystyrene EPS component binder is bonded with high quality bonded mortar, and is bonded by thin layer full adhesive method. The EPS component is extruded by force, so that the mortar spills from the periphery and the bonding seam width is no more than 3mm. The bond seam shall be glued with the stick, and the seam is full, and the surface of the EPS member is kept neat.
After understanding the EPS decoration line technology and its construction plan, I believe that you should use more choice in the later corner modeling. Although the decoration does not have to experience relatives, it is necessary to understand the related construction technology. In this way, in the process of decoration, can avoid the decoration company to fool. Or at the time of acceptance, it can be seen through the surface to see whether the construction technology is qualified. While a more worry method is to choose a tuba rabbit, involved in the third party supervision decoration platform, with the help of EPS, such as similar decorative line construction of the standard process, completely no longer need to view the Internet construction case.